About 'SemiQSK’
-
- Posts: 7
- Joined: 07 Sep 2022, 15:03
About 'SemiQSK’
I use it in SOTA CW. It is very good, but
In CW mode with 'SemiQSK' ON, the first character is missing when switching to receive.
So when I turn off 'SemiQSK' and use full break in, the key click noise during transmission is too loud and it is hard to use.
1. Is it possible to speed up the switching time between TX and RX for 'SemiQSK' ?
2. Is it possible to reduce the key click noise when transmitting ?
In CW mode with 'SemiQSK' ON, the first character is missing when switching to receive.
So when I turn off 'SemiQSK' and use full break in, the key click noise during transmission is too loud and it is hard to use.
1. Is it possible to speed up the switching time between TX and RX for 'SemiQSK' ?
2. Is it possible to reduce the key click noise when transmitting ?
-
- Posts: 399
- Joined: 30 Dec 2021, 22:54
Re: About 'SemiQSK’
Hello OM Yoshihiro,
i think you maybe changed Att and Att 2 settings in Menue,
never had a problem with full bk and truSDX or the former uSDX.
Keep Att 2 at the default value.
You can reset by Pressing Tuning Knob at connecting your truSDX to power supply.
There is no possibility to change it in Menue.
Possible Hardware defect (maybe partly damaged) RXmute MosFet Q1 2N7002....
73 de Chris DL6SEZ
i think you maybe changed Att and Att 2 settings in Menue,
never had a problem with full bk and truSDX or the former uSDX.
Keep Att 2 at the default value.
You can reset by Pressing Tuning Knob at connecting your truSDX to power supply.
There is no possibility to change it in Menue.
Possible Hardware defect (maybe partly damaged) RXmute MosFet Q1 2N7002....
73 de Chris DL6SEZ
Chris DL6SEZ, JN48XL near Ulm, Southern Germany
-
- Posts: 7
- Joined: 07 Sep 2022, 15:03
Re: About 'SemiQSK’
Hello OM Chris,
Thanks for your comment.
The ATT settings are still at default, I did a factory reset just to be sure, but it did not improve the situation.
I did a 30 minute test run today with 40mBand and was able to communicate with 11 stations without any problems. The output power was 3W.
I am only concerned about the key click noise.
When I turn on SemiQSK, I don't hear the noise, but the RX switching is slow and the first character is missing, so I can't communicate smoothly.
73 de yosihiro JJ3IUS
Thanks for your comment.
The ATT settings are still at default, I did a factory reset just to be sure, but it did not improve the situation.
I did a 30 minute test run today with 40mBand and was able to communicate with 11 stations without any problems. The output power was 3W.
I am only concerned about the key click noise.
When I turn on SemiQSK, I don't hear the noise, but the RX switching is slow and the first character is missing, so I can't communicate smoothly.
73 de yosihiro JJ3IUS
-
- Posts: 399
- Joined: 30 Dec 2021, 22:54
Re: About 'SemiQSK’
Hello OM Yoshihiro,
nice setup for Sota
I have an idea to maybe reduce the "click" between signs in CW QSK .... not sure only thought about the circuit.....
Perhaps you can check to change C14 10µF to a lower value, i think this possibly could reduce the loudness of the clicks. It is possible that the click is a result of a Pullup Resistor switched off/on in the Atmega328 when Audio output is switched from sidetone generating to RX and wise versa.
It is clear that reducing C14 will result in a higher cutoff frequency at the lower end in the audio signals.
73 de Chris DL6SEZ
nice setup for Sota
I have an idea to maybe reduce the "click" between signs in CW QSK .... not sure only thought about the circuit.....
Perhaps you can check to change C14 10µF to a lower value, i think this possibly could reduce the loudness of the clicks. It is possible that the click is a result of a Pullup Resistor switched off/on in the Atmega328 when Audio output is switched from sidetone generating to RX and wise versa.
It is clear that reducing C14 will result in a higher cutoff frequency at the lower end in the audio signals.
73 de Chris DL6SEZ
Chris DL6SEZ, JN48XL near Ulm, Southern Germany
-
- Posts: 709
- Joined: 30 Dec 2021, 19:18
- Contact:
Re: About 'SemiQSK’
Hi Yoshihirio,
Thanks for your feedback, that indicates some serious high speed cw to me. Way to go !
I did not realize the problems you describe, as I´m not using Full QSK regularly and I´m not that fast, so Semi QSK would swallow the first letter of the reply. So I will check if I can repeat your findings, and I´m already in contact with Guido about it.
73 Manuel; DL2MAN
-
- Posts: 7
- Joined: 07 Sep 2022, 15:03
Re: About 'SemiQSK’
Thank you for your replies, Chris and Manuel.
I have uploaded a video of the key click noise.
https://youtu.be/_vYgCQ-3DgM
I will not be replacing the C14 capacitor as it is difficult to do.
I expect QSK timing to improve.
73 TU
I have uploaded a video of the key click noise.
https://youtu.be/_vYgCQ-3DgM
I will not be replacing the C14 capacitor as it is difficult to do.
I expect QSK timing to improve.
73 TU
-
- Posts: 709
- Joined: 30 Dec 2021, 19:18
- Contact:
Re: About 'SemiQSK’
Could you please tell us, what software version you are using ?
73 Manuel DL2MAN
73 Manuel DL2MAN
-
- Posts: 7
- Joined: 07 Sep 2022, 15:03
Re: About 'SemiQSK’
Version is 2.00i.
I have adjusted the RF board and am using it in Classic mode.
73 yoshihiro JJ3IUS
I have adjusted the RF board and am using it in Classic mode.
73 yoshihiro JJ3IUS
-
- Posts: 709
- Joined: 30 Dec 2021, 19:18
- Contact:
Re: About 'SemiQSK’
Hello Yoshihiro,
I have confirmed the bahavior on 3 Rigs, and we are trying to improve the behavior by Software.
73 Manuel; DL2MAN
I have confirmed the bahavior on 3 Rigs, and we are trying to improve the behavior by Software.
73 Manuel; DL2MAN
-
- Posts: 24
- Joined: 06 Feb 2022, 08:28
- Location: Edgewater, FL
Re: About 'SemiQSK’
Manuel,
This is great news and has been mentioned before but never addressed.
Thank you, I am also looking for your final results on 'key clicks'.
Bill - W3SI
-
- Posts: 7
- Joined: 07 Sep 2022, 15:03
Re: About 'SemiQSK’
Hello Manuel,
Thank you very much for responding to my questions.
I hope the operation will be better.
73 Yoshihiro, JJ3IUS
Thank you very much for responding to my questions.
I hope the operation will be better.
73 Yoshihiro, JJ3IUS
Users browsing this forum: No registered users and 1 guest