Hello!
I need help. My trusdx is delivered from approved supplier at Alliexpress.
I adjusted power and efficiency at all bands.
When I press and release PTT in CW mode the trusdx remains 5-6s in TX, before going to RX. I found this problem during power and efficiency adjustment at 80m. At other bands no similar problems. What to do here to solve this problem?
73 de neven, 9A5YY
Problem with TX and RX, CW mode at 80m
-
- Posts: 9
- Joined: 12 Aug 2022, 02:24
Re: Problem with TX and RX, CW mode at 80m
Does this happen using the internal PTT switch or with an external key/switch?
Are you transmitting into a dummy load or an antenna?
Trying to rule out RF as cause.
73 John N8JJO
Are you transmitting into a dummy load or an antenna?
Trying to rule out RF as cause.
73 John N8JJO
-
- Posts: 21
- Joined: 03 Jan 2022, 22:16
Re: Problem with TX and RX, CW mode at 80m
Hello John!
It happens when using internal PTT switch and external keyer.
I use dummy load. This is my second trusdx. With the first one I did't have this problem.
It happens when using internal PTT switch and external keyer.
I use dummy load. This is my second trusdx. With the first one I did't have this problem.
-
- Posts: 21
- Joined: 03 Jan 2022, 22:16
Re: Problem with TX and RX, CW mode at 80m
Hello!
I wanted to upload bootloader to my trusdx with Arduino programmer because I didn't see Serial Number when trusdx was powered up for the first time. I don't know why but I didn't succeed to upload bootloader.
Something was wrong. Finally I successfully updated firmware once again. It seems my problem with CW at 80m disappeared with updated firmware.
73 de Neven, 9A5YY
I wanted to upload bootloader to my trusdx with Arduino programmer because I didn't see Serial Number when trusdx was powered up for the first time. I don't know why but I didn't succeed to upload bootloader.
Something was wrong. Finally I successfully updated firmware once again. It seems my problem with CW at 80m disappeared with updated firmware.
73 de Neven, 9A5YY
-
- Posts: 9
- Joined: 12 Aug 2022, 02:24
Re: Problem with TX and RX, CW mode at 80m
Glad to hear you solved the issue!
73 John
73 John
-
- Posts: 21
- Joined: 03 Jan 2022, 22:16
Re: Problem with TX and RX, CW mode at 80m
Hello!
Finally, after few days I found out that the new firmware didn't solve problem with CW mode at 80m.
I contacted official trusdx supplier at Aliexpress Sunny. I described him problem and sent him video with problem. Sunny after watching video assumed that probably mainboard causes problem. He sent me new mainboard quickly. I soldered components and made OLED modification at the new mainborad. With the new mainboad used at my trusdx, the problem with CW mode at 80m disappeared. I can only assume that at my old mainboard something was soldered bad in factory. So, that's my story how I solved problem thanks to Sunny.
73 de Neven, 9A5YY
Finally, after few days I found out that the new firmware didn't solve problem with CW mode at 80m.
I contacted official trusdx supplier at Aliexpress Sunny. I described him problem and sent him video with problem. Sunny after watching video assumed that probably mainboard causes problem. He sent me new mainboard quickly. I soldered components and made OLED modification at the new mainborad. With the new mainboad used at my trusdx, the problem with CW mode at 80m disappeared. I can only assume that at my old mainboard something was soldered bad in factory. So, that's my story how I solved problem thanks to Sunny.
73 de Neven, 9A5YY
Users browsing this forum: No registered users and 24 guests