Cw message loop no function
-
- Posts: 5
- Joined: 04 Jun 2023, 07:23
Cw message loop no function
I accidentally sent without an antenna while the cw message was running. I quickly unplugged the power plug. The transistor was broken. I replaced it. Unfortunately, it no longer sends the cw message (loop). Which component could have been damaged? Reset has already been done.
-
- Posts: 712
- Joined: 30 Dec 2021, 19:18
- Contact:
Re: Cw message loop no function
If TXing normal CW works, there´s no more components involved in the loop part specificlly besides the microcontroller.
So i suggest:
1. Reset settings by pressing and holding rotary encoder while powering up.
if that doesn´t solve your issue
2. re-install firmware
if that doesn´t solve your issue
3. re-install bootloader, set fuses and re-install firmware
if all the above doesn´t work:
Your AtMega has a Problem and needs to be exchanged
73 Manuel; DL2MAN
So i suggest:
1. Reset settings by pressing and holding rotary encoder while powering up.
if that doesn´t solve your issue
2. re-install firmware
if that doesn´t solve your issue
3. re-install bootloader, set fuses and re-install firmware
if all the above doesn´t work:
Your AtMega has a Problem and needs to be exchanged
73 Manuel; DL2MAN
-
- Posts: 5
- Joined: 04 Jun 2023, 07:23
Re: Cw message loop no function
Reset done. I reuploaded the firmware. Nothing changed. I have to find someone with arduino flasher to upload bootloader again.
Is it possible to erase flash and write firmware? Or only write firmware.
Do i erase bootloader if i erase and flash Firmware?
Is it possible to erase flash and write firmware? Or only write firmware.
Do i erase bootloader if i erase and flash Firmware?
-
- Posts: 712
- Joined: 30 Dec 2021, 19:18
- Contact:
Re: Cw message loop no function
Bootloader is in a seperate memory area, that cannot be accessed via USB (RX/TX Port of Atmega), it can only be accessed via ICSP, so you´ll need a programmer of some kind.
https://dl2man.de/3a-trusdx-bootloader/
73 Manuel; DL2MAN
https://dl2man.de/3a-trusdx-bootloader/
73 Manuel; DL2MAN
-
- Posts: 5
- Joined: 04 Jun 2023, 07:23
Re: Cw message loop no function
Bootloader flashed again. It doesn’t fixed the problem.
I ordered atmega 328PB-AU. Is this correct? What does AU mean?
Is there something i have to look for, when i change it?
I ordered atmega 328PB-AU. Is this correct? What does AU mean?
Is there something i have to look for, when i change it?
-
- Posts: 5
- Joined: 04 Jun 2023, 07:23
Re: Cw message loop no function
It has fixed itself. I connected a morse key (bought new one). Then made the rig off. After i disconnected the key, there was something like insert key on the screen. I connected the key and heard a relais working. After that the loop was working again
-
- Posts: 712
- Joined: 30 Dec 2021, 19:18
- Contact:
Re: Cw message loop no function
Must have been the nanobots, that we used in this project.
Also known as fairydust
In all seriousness: I have no clue what happened to your rig or why....
73 Manuel; DL2MAN
Also known as fairydust
In all seriousness: I have no clue what happened to your rig or why....
73 Manuel; DL2MAN
Users browsing this forum: gatorjj and 35 guests