Please, help me (tr)uSDX doesn't work
-
- Posts: 7
- Joined: 05 Dec 2023, 22:41
Please, help me (tr)uSDX doesn't work
Hi, I'm a complete beginner.
I bought from the official source (tr)uSDX. Unfortunately, after connecting it, it is simply impossible to find any station to listen to. I don't know anymore, either it's factory set incorrectly or there's something wrong with it. How to make sure? I connected different antennas and always the same - nothing .
Additionally, I cannot access all menus. First it's 1.1, then 1.2 and then 1.8.
Please help, thank you in advance for your advice.
73, Przemek
I bought from the official source (tr)uSDX. Unfortunately, after connecting it, it is simply impossible to find any station to listen to. I don't know anymore, either it's factory set incorrectly or there's something wrong with it. How to make sure? I connected different antennas and always the same - nothing .
Additionally, I cannot access all menus. First it's 1.1, then 1.2 and then 1.8.
Please help, thank you in advance for your advice.
73, Przemek
-
- Posts: 12
- Joined: 15 Oct 2023, 17:46
- Location: UA
Re: Please, help me (tr)uSDX doesn't work
Try to set menu setting 1.1 to higher values, its sound volume. Also you can increase it by pressing knob and rotating...Do you at least hear noise sound?
Also try to connect headphones, maybe something wrong with speaker.
Also try to connect headphones, maybe something wrong with speaker.
-
- Posts: 7
- Joined: 05 Dec 2023, 22:41
Re: Please, help me (tr)uSDX doesn't work
Yes, I can hear the noise.
When you change the frequency, there is also a variable noise. But he doesn't take anything away.
When you change the frequency, there is also a variable noise. But he doesn't take anything away.
-
- Posts: 19
- Joined: 08 Aug 2023, 01:40
Re: Please, help me (tr)uSDX doesn't work
Przemek,
Hello. A good first step may be to check out the DL2MAN video in YouTube covering the (tr)uSDX menu options. It's sort of an intro video so you may find it interesting. BTW note that depending on the version of firmware that you have on your (tr)uSDX some menu options will or will not be displayed.
This is the URL for DL2MAN's video:
https://youtu.be/gW5r5JQRbus?si=VYs0GXQ36AAZasf9
Also, and this may be the thing to do first, is to update your CallSign in your new (tr)uSDX. This gets your feet wet regarding the transceiver. There are multiple videos in YouTube on how to do this; however, these are some i made that may be helpful to you.
This is the URL for the playlist:
https://youtube.com/playlist?list=PLh0u ... R6MAAMRh9e
Welcome to the community and I'm sure you'll knock this out in no time.
73,
Stephen
Hello. A good first step may be to check out the DL2MAN video in YouTube covering the (tr)uSDX menu options. It's sort of an intro video so you may find it interesting. BTW note that depending on the version of firmware that you have on your (tr)uSDX some menu options will or will not be displayed.
This is the URL for DL2MAN's video:
https://youtu.be/gW5r5JQRbus?si=VYs0GXQ36AAZasf9
Also, and this may be the thing to do first, is to update your CallSign in your new (tr)uSDX. This gets your feet wet regarding the transceiver. There are multiple videos in YouTube on how to do this; however, these are some i made that may be helpful to you.
This is the URL for the playlist:
https://youtube.com/playlist?list=PLh0u ... R6MAAMRh9e
Welcome to the community and I'm sure you'll knock this out in no time.
73,
Stephen
-
- Posts: 399
- Joined: 30 Dec 2021, 22:54
Re: Please, help me (tr)uSDX doesn't work
Hello OM Przemek,
don't try to change unnecessary things as "Quantumradio" (sorry: a silly name) proposed you, e,g. changing your call sign, until you know your (tr)uSDX works as it should. Changing your callsign is playing but has nothing to do with a working (tr)uSDX....
Which Version have you bought: Lo, classic or high band?
If you look in the menue and adjust it at item 8.7 to the right band version.
That's the only thing to do to get it working in receive.
Have a look at 40m is every time day/night a good choice with a few meters of wire 7m to 10m you must be able to find a cw station in the lower part of the band or at ft8 frequency the ft8ers.
73 de Chris
don't try to change unnecessary things as "Quantumradio" (sorry: a silly name) proposed you, e,g. changing your call sign, until you know your (tr)uSDX works as it should. Changing your callsign is playing but has nothing to do with a working (tr)uSDX....
Which Version have you bought: Lo, classic or high band?
If you look in the menue and adjust it at item 8.7 to the right band version.
That's the only thing to do to get it working in receive.
Have a look at 40m is every time day/night a good choice with a few meters of wire 7m to 10m you must be able to find a cw station in the lower part of the band or at ft8 frequency the ft8ers.
73 de Chris
Chris DL6SEZ, JN48XL near Ulm, Southern Germany
-
- Posts: 7
- Joined: 05 Dec 2023, 22:41
Re: Please, help me (tr)uSDX doesn't work
Hello Chris
I bought this version. (https://www.ebay.com/itm/134061787836)
I asked for a call sign. I guess, unfortunately? Due to ignorance about the versions,
I bought Lo (in the description I now read:
==================================================
"Current mainboard:1.2 version PCB
(tr)uSDX HF Ham Radio QRP CW Transceiver Full Kits by PE1NNZ and DL2MAN 5bands
Note: This link: It is the LO bands,not high bands,not classic bands."
=============================================================
But in menu 8.7 I can Lo, classic or high band, i.e. all 3 versions - but does it work after changing it?
Recently I bought the original "QRPGuys Portable No Tune End Fed Half Wave Antenna", I connected the 20m band cable and... nothing.
But as you advise, tomorrow I will cut the appropriate cable and try to catch something on the 40m band
Thank You
73, Przemek
I bought this version. (https://www.ebay.com/itm/134061787836)
I asked for a call sign. I guess, unfortunately? Due to ignorance about the versions,
I bought Lo (in the description I now read:
==================================================
"Current mainboard:1.2 version PCB
(tr)uSDX HF Ham Radio QRP CW Transceiver Full Kits by PE1NNZ and DL2MAN 5bands
Note: This link: It is the LO bands,not high bands,not classic bands."
=============================================================
But in menu 8.7 I can Lo, classic or high band, i.e. all 3 versions - but does it work after changing it?
Recently I bought the original "QRPGuys Portable No Tune End Fed Half Wave Antenna", I connected the 20m band cable and... nothing.
But as you advise, tomorrow I will cut the appropriate cable and try to catch something on the 40m band
Thank You
73, Przemek
-
- Posts: 7
- Joined: 05 Dec 2023, 22:41
Re: Please, help me (tr)uSDX doesn't work
QuantumRadio wrote: ↑22 Dec 2023, 15:12 I have my call sign entered into the receiver.
At this point, with my skills, I would be afraid to take risks and reset
Thank you for the links, I'll take a closer look
Thank you
73, Przemek
-
- Posts: 207
- Joined: 01 Jan 2022, 03:47
Re: Please, help me (tr)uSDX doesn't work
You let the software know which RF board you have, lo classic or hi, by making the correct selection in menu 8.7 It can’t figure it out on its own, you have to tell it.
The the actual RF board in use, and the board selected in the menu, have to match for the radio to work correctly.
For transmit you also have to set the “PA bias max” correctly.
The lo RF board uses 3 BS170s with PA bias max of 128.
The classic and hi boards use one FDT86256 with a PA bias max of 160.
The the actual RF board in use, and the board selected in the menu, have to match for the radio to work correctly.
For transmit you also have to set the “PA bias max” correctly.
The lo RF board uses 3 BS170s with PA bias max of 128.
The classic and hi boards use one FDT86256 with a PA bias max of 160.
-
- Posts: 7
- Joined: 05 Dec 2023, 22:41
Re: Please, help me (tr)uSDX doesn't work
How to unlock menus from 1.3 to 1.7?
Thanks, 73!
Thanks, 73!
-
- Posts: 59
- Joined: 03 Jan 2022, 21:11
- Location: Krakow
Re: Please, help me (tr)uSDX doesn't work
Przemek,
I'm not sure what you mean by unlock menus, but option
1.3 is a filter setting
1.4 is band selection
1.5 is tune rate
1.6 VFO
1.7 RIT
But to change any of the setting you press main VFO knob and then turn to select desired option.
To finish you press ENTER button.
Many options can be accessed through shortcuts here is a detailed description https://dl2man.de/4-trusdx-manual/
I'm not sure what you mean by unlock menus, but option
1.3 is a filter setting
1.4 is band selection
1.5 is tune rate
1.6 VFO
1.7 RIT
But to change any of the setting you press main VFO knob and then turn to select desired option.
To finish you press ENTER button.
Many options can be accessed through shortcuts here is a detailed description https://dl2man.de/4-trusdx-manual/
-
- Posts: 7
- Joined: 05 Dec 2023, 22:41
Re: Please, help me (tr)uSDX doesn't work
Hello Marek
No, what I mean is that there are NO items 1.3 to 1.7 on my menu.
By skipping one by one, I have in the menu:
1.1
1.2
1.8
1.12
1.13
next:
2.4 to 2.8
then 3.1 to 3.4
4.1 to 4.7
Without 8.1 and beyond:
8.2
8.3 and another break until
8.6
8.7
and next group:
9.7
And these are all the menu items.
Thank You.
Przemek
==================
Witaj Marku
Nie, chodzi mi o to, że w moim menu NIE ma pozycji od 1.3 do 1.7.
Przeskkując po kolei mam w menu:
1.1;
1.2;
1.8;
1.12
1.13
następnie:
2.4 do 2.8
potem 3.1 do 3.4
4.1 do 4.7
Bez 8.1 i dalej:
8.2
8.3 i znów przerwa do
8.6
8.7
i nastepna grupa:
9.7
I to są wszystkie pozycje menu.
--
Pozdrawiam serdecznie, Przemek.
No, what I mean is that there are NO items 1.3 to 1.7 on my menu.
By skipping one by one, I have in the menu:
1.1
1.2
1.8
1.12
1.13
next:
2.4 to 2.8
then 3.1 to 3.4
4.1 to 4.7
Without 8.1 and beyond:
8.2
8.3 and another break until
8.6
8.7
and next group:
9.7
And these are all the menu items.
Thank You.
Przemek
==================
Witaj Marku
Nie, chodzi mi o to, że w moim menu NIE ma pozycji od 1.3 do 1.7.
Przeskkując po kolei mam w menu:
1.1;
1.2;
1.8;
1.12
1.13
następnie:
2.4 do 2.8
potem 3.1 do 3.4
4.1 do 4.7
Bez 8.1 i dalej:
8.2
8.3 i znów przerwa do
8.6
8.7
i nastepna grupa:
9.7
I to są wszystkie pozycje menu.
--
Pozdrawiam serdecznie, Przemek.
-
- Posts: 59
- Joined: 03 Jan 2022, 21:11
- Location: Krakow
Re: Please, help me (tr)uSDX doesn't work
Hi Przemek,
What version of software do you have?
Jaką masz wersję firmware?
Marek
What version of software do you have?
Jaką masz wersję firmware?
Marek
-
- Posts: 399
- Joined: 30 Dec 2021, 22:54
Re: Please, help me (tr)uSDX doesn't work
Hello OM Przemek,
there are many missing menue points, this is normally now.
On the Manual page it is not up to date with the newest version!
As i said before, for your band version, switch at menue 8.7 to LO,
for TX there should be standard value 128 in Menue 8.1 TX bias. (would be 160 for classic or high band)
There is nothing more to be done to get all fully working if you bought a full built (tr)uSDX!
Don't forget: best is using headphones and Volume must be adjusted....
If it doesn't receive on 7Mhz 40m with a wire Antenna 7m to 10m in the evening than ask at the seller for a replacement or what you should do now.
We will help you here but a new bought ready built (tr)uSDX has to work or....
73 de Chris
there are many missing menue points, this is normally now.
On the Manual page it is not up to date with the newest version!
As i said before, for your band version, switch at menue 8.7 to LO,
for TX there should be standard value 128 in Menue 8.1 TX bias. (would be 160 for classic or high band)
There is nothing more to be done to get all fully working if you bought a full built (tr)uSDX!
Don't forget: best is using headphones and Volume must be adjusted....
If it doesn't receive on 7Mhz 40m with a wire Antenna 7m to 10m in the evening than ask at the seller for a replacement or what you should do now.
We will help you here but a new bought ready built (tr)uSDX has to work or....
73 de Chris
Chris DL6SEZ, JN48XL near Ulm, Southern Germany
-
- Posts: 7
- Joined: 05 Dec 2023, 22:41
Users browsing this forum: No registered users and 8 guests