About 'SemiQSK’

Post Reply
yoshihiro
 

Posts: 7
Joined: 07 Sep 2022, 15:03

About 'SemiQSK’

Post by yoshihiro »

I use it in SOTA CW. It is very good, but
In CW mode with 'SemiQSK' ON, the first character is missing when switching to receive.
So when I turn off 'SemiQSK' and use full break in, the key click noise during transmission is too loud and it is hard to use.
1. Is it possible to speed up the switching time between TX and RX for 'SemiQSK' ?
2. Is it possible to reduce the key click noise when transmitting ?
dl6sez
 

Posts: 399
Joined: 30 Dec 2021, 22:54

Re: About 'SemiQSK’

Post by dl6sez »

Hello OM Yoshihiro,

i think you maybe changed Att and Att 2 settings in Menue,
never had a problem with full bk and truSDX or the former uSDX.
Keep Att 2 at the default value.
You can reset by Pressing Tuning Knob at connecting your truSDX to power supply.
There is no possibility to change it in Menue.
Possible Hardware defect (maybe partly damaged) RXmute MosFet Q1 2N7002....

73 de Chris DL6SEZ
Chris DL6SEZ, JN48XL near Ulm, Southern Germany
yoshihiro
 

Posts: 7
Joined: 07 Sep 2022, 15:03

Re: About 'SemiQSK’

Post by yoshihiro »

Hello OM Chris,
Thanks for your comment.

The ATT settings are still at default, I did a factory reset just to be sure, but it did not improve the situation.
I did a 30 minute test run today with 40mBand and was able to communicate with 11 stations without any problems. The output power was 3W.

I am only concerned about the key click noise.
When I turn on SemiQSK, I don't hear the noise, but the RX switching is slow and the first character is missing, so I can't communicate smoothly.

73 de yosihiro JJ3IUS
test.jpg
test.jpg (109.97 KiB) Viewed 1579 times
dl6sez
 

Posts: 399
Joined: 30 Dec 2021, 22:54

Re: About 'SemiQSK’

Post by dl6sez »

Hello OM Yoshihiro,

nice setup for Sota :D
I have an idea to maybe reduce the "click" between signs in CW QSK .... not sure only thought about the circuit.....
Perhaps you can check to change C14 10µF to a lower value, i think this possibly could reduce the loudness of the clicks. It is possible that the click is a result of a Pullup Resistor switched off/on in the Atmega328 when Audio output is switched from sidetone generating to RX and wise versa.
It is clear that reducing C14 will result in a higher cutoff frequency at the lower end in the audio signals.

73 de Chris DL6SEZ
Chris DL6SEZ, JN48XL near Ulm, Southern Germany
DL2MAN
 

Posts: 706
Joined: 30 Dec 2021, 19:18
Contact:

Re: About 'SemiQSK’

Post by DL2MAN »

yoshihiro wrote: 10 Sep 2022, 13:48 I am only concerned about the key click noise.
When I turn on SemiQSK, I don't hear the noise, but the RX switching is slow and the first character is missing, so I can't communicate smoothly.

73 de yosihiro JJ3IUS
test.jpg
Hi Yoshihirio,

Thanks for your feedback, that indicates some serious high speed cw to me. Way to go !
I did not realize the problems you describe, as I´m not using Full QSK regularly and I´m not that fast, so Semi QSK would swallow the first letter of the reply. So I will check if I can repeat your findings, and I´m already in contact with Guido about it.

73 Manuel; DL2MAN
yoshihiro
 

Posts: 7
Joined: 07 Sep 2022, 15:03

Re: About 'SemiQSK’

Post by yoshihiro »

Thank you for your replies, Chris and Manuel.

I have uploaded a video of the key click noise.
https://youtu.be/_vYgCQ-3DgM

I will not be replacing the C14 capacitor as it is difficult to do.
I expect QSK timing to improve.

73 TU
DL2MAN
 

Posts: 706
Joined: 30 Dec 2021, 19:18
Contact:

Re: About 'SemiQSK’

Post by DL2MAN »

Could you please tell us, what software version you are using ?

73 Manuel DL2MAN
yoshihiro
 

Posts: 7
Joined: 07 Sep 2022, 15:03

Re: About 'SemiQSK’

Post by yoshihiro »

Version is 2.00i.

I have adjusted the RF board and am using it in Classic mode.

73 yoshihiro JJ3IUS
DL2MAN
 

Posts: 706
Joined: 30 Dec 2021, 19:18
Contact:

Re: About 'SemiQSK’

Post by DL2MAN »

Hello Yoshihiro,

I have confirmed the bahavior on 3 Rigs, and we are trying to improve the behavior by Software.

73 Manuel; DL2MAN
W3SI
 

Posts: 24
Joined: 06 Feb 2022, 08:28
Location: Edgewater, FL

Re: About 'SemiQSK’

Post by W3SI »

DL2MAN wrote: 19 Sep 2022, 07:30 Hello Yoshihiro,

I have confirmed the bahavior on 3 Rigs, and we are trying to improve the behavior by Software.

73 Manuel; DL2MAN
Manuel,

This is great news and has been mentioned before but never addressed.
Thank you, I am also looking for your final results on 'key clicks'.

Bill - W3SI
yoshihiro
 

Posts: 7
Joined: 07 Sep 2022, 15:03

Re: About 'SemiQSK’

Post by yoshihiro »

Hello Manuel,

Thank you very much for responding to my questions.
I hope the operation will be better.

73 Yoshihiro, JJ3IUS
Post Reply

Users browsing this forum: No registered users and 1 guest